By the Authority Vested By Part 5 of the United States Code § (a) and. Part 1 of the Code of Regulations § 51 the attached document has been duly. Find the most up-to-date version of SAE J at Engineering SAE Technical Standards Board Rules provide that: “This report is published . SAE J—Automobile, Truck, Truck-Tractor, Trailer, And Motor Coach Wiring.
|Published (Last):||17 December 2005|
|PDF File Size:||6.82 Mb|
|ePub File Size:||3.9 Mb|
|Price:||Free* [*Free Regsitration Required]|
Clips for retaining cables and har.
Standard: SAE J1292
The Sae j1292 makes several minor clerical corrections regarding the rear license plate lamp requirements and the periodic inspection requirements for antilock brake systems ABS. Wiring shall be protected from stones, excess dirt, ice, moisture, chafing, and so forth, that will result in harmful effects. Wiring exposed to such conditions shall be further protected by either, or a combination of, the use of heavy wall thermoplastic insu- lated cable, see SAE Standard J, Low Tension Primary Cable additional tape application, plastic sleeving or conduit, nonmetallic loom, or metallic or other suitable shielding or covering.
Wiring connections to lights mounted on the coach body shall be accessible from outside, with the light removed or through an access door in an interior trim panel. Sae j1292 — In many cases 4 or 6 gauge may be required. The main ground wire sae j1292 be a minimum of sae j1292.
This is written principally for new vehicles but is also applicable to rewiring and service. The proposed FMVSS would also require each vehicle, as manufactured and sold, to have its device set to a speed not greater than a specified speed and to be equipped with means of reading the vehicle’s sae j1292 speed setting and the two previous speed settings including the time and date the settings were changed through its On-Board Diagnostic connection.
Ground terminals shall be accessible for service: Consideration is given to physical and environmental factors such as flex- ing, heat, cold, bend, oil and fuel contact, sae j1292, abrasion, short circuit, and pinch resistance sae j1292 others.
Double trailer combinations consisting of a tractor, a semitrailer, and a trailer are also common. To be acceptable, a sheath or tube must enclose the wires throughout their circumference. We expect that, as a sae j1292 of this joint rulemaking, virtually all of these vehicles would be limited to that speed. More limitations on accuracy are described at the GPO site. NOTE— Contact of the trailer king pin or apron plate with the lower sae j1292 or grounding through the sae j1292 is not to be considered as providing a tractor-to-trailer ground.
Clips also assist in locating and routing at assembly. Based on the agencies’ review of sae j1292 available data, limiting the speed of these heavy vehicles would reduce sae j1292 severity of crashes involving these vehicles and reduce the resulting fatalities and injuries.
Wiring so located that it will be subjected to more than normal wear or hard usage shall be equipped with a means of disconnecting from the main harness and be easily removable for replacement or repair. Suitable tubing or conduit over sae j1292 may be substituted for grommets if properly secured. To view interpretations for a different section, click sae j1292 the menu item. Items that dictate the design are: Search the history of over billion web pages on the Internet. This final rule is effective October 24, Title 49 – Transportation.
SAE J1292: Automobile, Truck, Truck-Tractor, Trailer, and Motor Coach Wiring
Structure of sqe trailer, and c. This rule does not make any substantive changes to the affected regulations, except to remove one obsolete sae j1292. ArcelorMittal requests this exemption to allow its employee-drivers to work up to 16 hours per day and be allowed to return to work with less than the mandatory 10 consecutive hours off duty. Sae j1292 SAE Recommended Practice j12992 the application of primary wiring distribution system harnesses to automotive, and Motor Coach vehicles.
Resistance wire low tension cable may be used to limit the voltage applied to electrical m1292. These vehicles are allowed in all States, sae j1292 the weight allowed depends on axle limits and axle spacing. It is further desirable sae j1292 all motor vehicle manufacturers to assign and use similar color code information for commonly used electrical circuits to promote ease of circuit analysis in service among the various manufacturers.
Avoid areas of excessive heat, vibration, arid abrasion.
Suitable tubing or conduit over cables may be substituted for grommets if properly secured. Secondary applications will dictate the use of special terminations for special use or application. Circuit protection shall be accomplished by utilizing fuses, circuit break- ers, or fusible links which conform to SAE Standards. The Sae j1292 is making minor changes to correct sae j1292 and omissions, ensure conformity with Office sae j1292 the Federal Register style guidelines, update cross references, restore an inadvertent deletion of the reference to an Underwriters Laboratories’ saae, and improve clarity and consistency of certain regulatory provisions.
Ground Vehicle Standards No. SAE J Version – Download Manu
IHS Standards Expert subscription, simplifies and expedites the process for finding and managing standards by giving you access to standards from over sae j1292 developing organizations SDOs.
It covers the areas of performance, operating integrity, efficiency, economy, uniformity, facility of manufacturing and service. The sae j1292 changes went into effect on October sae j1292,retroactively, and require that FMCSA make conforming changes to its regulations saae ensure they are current and consistent with the statutory requirements. NHTSA and FMCSA have received requests to extend the comment period for their proposal that would require vehicles with a gross vehicle weight rating of more than 11, To ensure that all interested parties have a sufficient amount of time to fully develop their comments, the Agencies are extending the deadline for the submission of written comments on the proposal, including comments on the Preliminary Regulatory Impact Analysis and Initial Regulatory Flexibility Analysis and Draft Environmental Assessment accompanying the proposal, by 30 days.
It is desirable to identify, 1j292 wire by printing the words resistance wire on the conductor. This is written principally for sae j1292 vehicles but sae j1292 also applicable to rewiring and service.
Cornell Law School Search Cornell. The first exemption request is for ArcelorMittal’s employee-drivers with commercial sae j1292 licenses CDLs who sae j1292 steel coils between their production and shipping sae j1292 on public roads. NOTE — Extra protection such as braid, loom, conduit, etc.
Headlight systems shall be independently pro- tected. The reference to SAE J shall not be construed to require circuit protection on trailers. Clips for retaining cables and har- nesses shall be securely attached to body or frame member and cable or harness. If the certification label is missing, the motor carrier must obtain, and a driver upon demand present, a sae j1292 issued by the vehicle manufacturer stating that the vehicle met all applicable FMVSS in effect at the time of manufacture.