Mitsubishi E Variable frequency drive (VFD) Instruction Manual – Free ebook download as PDF File .pdf), Text File .txt) or read book online for free. Thank you for choosing this Mitsubishi Inverter. This Instruction Manual provides instructions for advanced use of the FR-E series inverters. Incorrect. Thank you for choosing this Mitsubishi Inverter. This Instruction Manual (basic) is intended for users who “just want to run the inverter”. If you are going to utilize.
|Published (Last):||26 January 2018|
|PDF File Size:||18.91 Mb|
|ePub File Size:||10.6 Mb|
|Price:||Free* [*Free Regsitration Required]|
Note that tuning performance is unaffected even if the motor runs slightly. Led Display Troubleshooting LED display LED display There are the following correspondences between the actual alphanumeric characters and the digital characters displayed on the operation panel. Initial Setting Refer to Name Since these inverrter have the mitsubishi e700 inverter manual serial numbers, always reinstall the removed cover onto the ori- ginal inverter. If the values mitsubishi e700 inverter manual be displayed have five digits or more including decimal places, the fifth or later numerals can not be displayed nor set.
Stall prevention operation performed during invetrer speed may cause sudden speed changes.
Mitsubishi Electric FR-E700 Instruction Manual
FR-E EC 8 – Page Initial value change list Displays the parameters changed from the initial value. Change The Control Method pr. When either is Mitsubushi, the operation mode cannot be changed. For details, refer to section 6. Page Selection of operation mode and operation location Parameter Switching of command source by external mitsubishi e700 inverter manual X67 In the network operation mode, the command source switching signal X67 can be used to switch the start command source and speed command source.
MITSUBISHI ELECTRIC FR-E INSTRUCTION MANUAL Pdf Download.
Never connect mitsubishi e700 inverter manual power cable mitsubishi e700 inverter manual the U, V, W of the inverter. Adjust the output torque current of the motor Parameter Setting of stall prevention operation in high frequency range Pr. Page yet received any control commands. When the wiring length is long 50m or more for the V class small-capacity model FR-E or lessthe external thermal relay invetter likely to operate unnecessarily because the ratio of the leakage current to the rated motor current increases.
Operation setting at alarm occurrence Parameter Manua Pr. Set “50”Hz to Pr. For the terminal used for REX signal input, set “8” in any of Pr.
Page – Mitsubishi inverter protocol computer l Differ- ent setting may cause a fault, failure or malfunction. Other manufacturer’s standard motor — Other manufacturer’s constant torque motor — Tab. Motor noise, EMI measures, mechanical resonance Mitsubishi e700 inverter manual 6. Inveeter of operation mode and operation location Parameter Selects the command source of the PU operation mode Pr.
However, it can be set any time when the communication e7000 is connected. Page Therefore, if the instantaneous power fai- lure time exceeds 0. Output signal output This signal turns OFF during power failure or undervoltage. Page The motor speed fluctuation at load fluctuation can be adjusted using Pr. Inverter may be damaged.
Page Iinverter vibration becomes large by increasing mitsubishi e700 inverter manual Pr. Tighten them according to the specified tighten- ing torque. Press to display the following.
Mitsubishi e700 inverter manual the carrier frequency exceeds 5kHz, do not use this instrument since using it may increase eddy-current losses produced in metal parts inside the instrument, leading to burnout. Page Control modes Adjust the output torque current of the motor Parameter 6.
From the operation panel Disabled From communication communication option Communication frequency setting Connection of communication option command sending Refer to the corresponding commu- Pr.
Press the SET key to set. Page You can find a detailed description of the operation panel with mitsubishi e700 inverter manual in section 4.
Operation outside this range will con- siderably shorten the service lives of the semiconductors, parts, capacitors and others. Page 47 Refer to section 6. Page When the motor does not stop due to large load moment Jincreasing the setting produces an effect. Operation selection at power failure Parameter If offline auto tuning ended mitsubishi e700 inverter manual error see the table belowmotor constants are not set.
Mitsubishi FR-E700 2.2kW 230V 1ph to 3ph – AC Inverter Drive Speed Controller
Frequency setting by analog input terminal 2, 4 Parameter Perform operation by analog input current When the pressure or temperature is controlled constant by a fan, pump, mitsubishi e700 inverter manual.
Perform an inverter reset and restart tuning. Auto tuning is not excecuted properly.