SO 4 SO 4 Elektroliza wody w roztworze H 2 SO 4 – + O H H O H H H H H H Kouichi Yuasa (Pl: ) H H H O O H H H H O H H O H H O H H O H H O H H. ELEKTROLIZA NaCl. JS. Joanna Setla. Updated 9 May Transcript. Główną zaletą metody przeponowej jest możliwość dostarczania. do zakładu nie soli. Innym sposobem otrzymywania wodorotlenku miedzi jest elektroliza wody z niedużą ilością rozpuszczonego siarczanu miedzi z użyciem miedzianej anody.

Author: Akinosho Zular
Country: Ukraine
Language: English (Spanish)
Genre: Love
Published (Last): 15 April 2009
Pages: 247
PDF File Size: 6.6 Mb
ePub File Size: 9.56 Mb
ISBN: 323-7-74062-277-2
Downloads: 50851
Price: Free* [*Free Regsitration Required]
Uploader: Miramar

The gas produced by electrolysis is very dangerous and should you decide to experiment with it, you do so wholly at your own risk. The output from the electronics board is about The bolts tapped into the inner tubes should be on the inside and the bottom eektroliza the two tubes aligned in spite of them being spread out as shown above.

We do not want that to happen.

Hardware stores sell large plastic buckets with air tight lids that can be used for this purpose. LED 8 – the 8 volt supply – should be lit when the power is connected and off when powered down.

Install capscrew with SS nut.

Category:Electrolysis – Wikimedia Commons

These include the necessary surface area of each electrode, the ‘conditioning’ of the electrodes and dealing with bubbles. And the L grade stainless steel, seamless tubes: Instead of running a small tube down the carburettor intake of each cylinder, it is more convenient and economic to use the existing intake manifold, leave the throttle wide open and run the hydroxy gas pipe into the manifold.

As we would like to have between two and four square inches of plate area per amp of current flowing through the plate surface, that means that each disc could carry anything from 6. Pour the dilute solution back into the electrolyser and repeat this cleaning process. The current is controlled by the concentration of Potassium Hydroxide in the electrolyte water plus KOH and the voltage across the cell.


Hydroxy gas is highly explosive, much more so than hydrogen on wodg own, and very much more dangerous than petrol vapour, burning at least 1, times faster.

It is not obvious why Stan drew it that way, as you would expect all six outer tubes to be wired in parallel in the same way as the inner tubes are.

Bob has specified that the primary windings are connected between the board outputs and the positive supply for the board like this: The only possible reason which suggests itself is that there is slightly less physical construction needed for the recommended way shown here: The plates in the middle are notionally touching each other. One major difference is that hydroxy gas rlektroliza very much faster than petrol vapour.


When your new printed circuit board is delivered, you will need the components to be mounted on it. It is peculiar in that the positive pulses from each stator winding shown in red in the circuit diagram are applied to just two of the outer pipes, while the negative pulses shown in blue in the circuit epektroliza are applied to all six inner tubes. The only drawback is that when stored at pressure, monatomic hydrogen reverts to its more common diatomic form. The power which heats the electrolyte is about Plastic is a common choice elektroljza the material and fittings are easy to find.

The question arises then, if these things are so dangerous, why do people want to construct them? J1 is shorted to shut down waveform generation.


So divide the number of turns in your secondary winding by 2. For that reason, it is absolutely essential that the toroid transformer is never powered up with the secondary winding connected to anything other than the filled electrolyser. Take the plates out of the electrolyser and start over again from plate preparation.

Also, this solution does not improve the overall efficiency of the process. This gives 1″ overlap. Media in category “Electrolysis” The following 69 files are in this category, out of 69 total. The tubes in this replication are made of L grade stainless steel, five inches long although Stan’s tubes were about three times that length. This is a long task, but it is vital that it is not skimped or hurried in any way. This is also an important feature because, should any malfunction occur in the electrolyser cell which causes a continuously increasing current to be drawn such as undue overheating of the cellthen the circuit breaker disconnects the link and prevents any serious problem arising.

There are two wire connection terminals available so that two equal length wires may be used to reduce wire resistance losses.

While Sodium Hydroxide works well and is much easier to get ‘Red Devil’ lye found in most department stores than the slightly more efficient Potassium Hydroxide.