This manual describes the use of all models in the series and gives instruction compatibility covers a broad range of ITU-T and BELL standards, and. Learn how to reboot your Sagemcom modem from Bell Business Internet. SG broadband routers & modems – Sagemcom [email protected] VDSL Wireless The device is used by Bell Canada and also known as “Bell.

Author: Monris Tara
Country: Costa Rica
Language: English (Spanish)
Genre: Travel
Published (Last): 8 August 2005
Pages: 497
PDF File Size: 17.18 Mb
ePub File Size: 7.36 Mb
ISBN: 593-7-80187-705-1
Downloads: 69376
Price: Free* [*Free Regsitration Required]
Uploader: Brajas

Retrieved from ” https: Comments to this Manuals Your Name. This page was last edited on 26 Octoberat Privacy policy About Support Disclaimers. The page requests a login with Bell credentials which our members can’t complete. The modem should now connect, although it may take several minutes to complete the connection and give a blue “in service” ” ” light indicating internet service is available. Rear Bottom USB Navigation menu Personal tools Log in.

Sagemcom 2864 Configuration

Don’t show me this message again. The Sagemcom Router Router is a powerful yet simple communication device for connecting your computer or local area network LAN to the Internet. The Sagemcom does not come with any manuals and there do not seem to be any manuals available on the company website.

No configuration should be attempted until this is complete. To establish a connection from your computer to the Router: From this sagemccom on, you will perform all configuration of the Sagemcom Router from your computer using the Web browser-based setup program.

If it is unknown then do a reset to factory default, using a paper-clip in the reset hole on the back. If the modem was previously configured for someone else, the password would be the previous user’s DSL password.



By pressing ‘print’ button you will print only current page. A firmware update may result in the loss of user name and password in which case the modem will only connect to the one Bell sign-up website, as mentioned above.

A line filter may be included with some manuzl prevents DSL traffic from disrupting the belp signal on the telephone line, and vice versa. The Sagemcom doesn’t act like other modems after a factory reset. If the modem is connected to the internet after a reset it will sign on and connect, but will only go to a single Bell website intended to allow Bell customers to sign up.

If the problem persists, contact Sagemcom Technical Support at the following number.

Official website | Sagemcom

Introduction Introduction Congratulations on the purchase of the Sagemcom Router. This troubleshooting section can help you identify and solve some of these issues. Got it, continue to print. Basic Troubleshooting Steps Before contacting Technical Support, you should attempt to sagmecom the issue by following these steps: The correct credentials need to be put back into the modem.

While most modems erase the password, reset everything to factory defaults and thus will not connect, the Sagemcom does not erase the password, but it does reset everything else to factory defaults. When connecting the Sagemcom for the first time and occasionally on subsequent connections, the LED near the ‘ ‘ symbol will flash red indicating that a firmware update is in progress. Page 2 This ebll was intentionally left Blank It’s possible that a power cycle may be eagemcom to get the modem to recognize the configuration change so if a “Save” doesn’t restore your Internet, try that.


Table of Contents Add to my manuals Add. No special wiring or cooling requirements are needed; however, you shall comply with the safety guidelines specified in the General Safety Guidelines section. Enter text from picture: Testing shows that that by default the firewall is on and all ports are closed and non-responsive, except Port 22 SSHwhich is closed but responds. Hold until the power light turns off to reset. The user name and password will now be as above.

Installation Installation Installation This chapter covers the physical installation of the Sagemcom Router.

Follow the step-by-step instructions below for installation.

Sagemcom [email protected] 2864

Views Read View source View history. Contacting Technical Support If you still cannot resolve manuxl issue after following the recommended troubleshooting procedures, first contact your ISP.

Page of 23 Go. There may be a remote risk of electric shock from lightning. Don’t have an account?

You will need to enter the current Password before entering the new Password two times. To print the manual completely, please, download it. NCF members can disregard this and proceed to configure the modem to connect to NCF’s internet service.

The modem interface GUI does not offer any means of configuring the modem’s firewall. If this occurs then leave the modem on until the LED is no longer flashing red.

This is an indication that it needs to be reconfigured with this information.