Full text of “IC Datasheet: EPROM” Jameco Part Number M NMOS Kbit (32Kb x 8) UV EPROM NOT FOR NEW DESIGN □ FAST. datasheet, pdf, data sheet, datasheet, data sheet, pdf, General NMOS K 32K x 8 UV EPROM Others with the same file for datasheet. (EPROM). The device is organized as 32K words by 8 bits (32K bytes). Accessing individual bytes from an address transition or from power-up (chip enable pin.
|Published (Last):||1 February 2012|
|PDF File Size:||2.66 Mb|
|ePub File Size:||10.26 Mb|
|Price:||Free* [*Free Regsitration Required]|
Specifications mentioned in this publication are subject to change without notice. Program Inhibit Programming of multiple Ms in parallel with different data is also easily accojnplished.
No license is granted by implication or otherwise under any patent or patent rights of STMicroeiectronics. The length of the Over-program Pulse varies from 2. All other address lines must be held at Vil during Datadheet Signature mode. STIVIicroelectronics products are not authorized for use as critical components in life support devices or systems without express written approval of STMicroeiectronics.
27256 – 27256 256K EPROM Datasheet
The data to be pro- grammed is applied 8 bits in parallel to the data output pins. The magnitude of the transient current peaks is dependent on the capacitive and inductive loading of the device at the output.
The integrated dose i. Data is introduced by selectively programming “Os” into the desired bit locations.
The recommended erasure procedure for the M is exposure to short vyave ultraviolet light which has wavelength A. Two identifier bytes may then be sequenced from the device outputs dataasheet toggling address line AO from Vil to Vih. Program Verify A verify should be performed on the programmed bits to determine epom they were correctly pro- grammed. These are stress ratings oniy and operation of the device at these or any other conditions above those indicated in the Operating sections of this specification is not implied.
The two line control function allows: The levels required forthe address and data inputs are TTL. When parallel programming dataeheet devices which share the common bus, Vpp should be lowered to Vcc 6V and the normal read mode used to exe- cute a program verify.
A single 5V power supply is required in the read mode. Full text of ” IC Datasheet: It is recommended that a 1 j.
Data s available at the adtasheet after the falling edge of G, assuming that E has been low and the ad- dresses have been stable for at least tAvav-tcLov. When in the standby mode, the outputs are in a high impedance state, independent of the G input. Search the history of over billion web pages on the Internet.
The M should be placed within 2.
If the M is to be exposed to these types of lighting conditions for extended periods of time, it is suggested that opaque lables be put over the M window to prevent unintentional erasure. It is organized as In addition, a 4. Except for E, all like inputs including G of the parallel M may be common. The Fast Programming Algorithm utilizes two different pulse types: Two Line Output Control Because EPROMs are usually used in larger mem- ory arrays, this product features a 2 line control function which accommodates the use of multiple memory connection.
It should be noted that sunlight and some type of fluorescent lamps have wavelengths in the A range. The associated transient voltage peaks can be sup- pressed by complying with the two line output control and by properly selected decoupling ca- pacitors. This ensures that all deselected memory devices are in their low power standby mode eprim that erom output pins are only active when data is required from a particular memory device.
Vcc must be applied simultaneously with or before Vpp and removed simultaneously or after Vpp.
Full text of “IC Datasheet: EPROM”
Although only “Os” will be programmed, both “1 s” and “Os” can be present in the data word. The only way to change a “0” datasbeet a “1 ” is by ultraviolet light erasure.
The duration of the initial E pulse s is 1 ms, which will then be followed by a longer over- program pulse of dxtasheet 3ms by n n is equal to the number of the initial one millisecond pulses applied Table 3. The transparent lid allows the user to expose the chip to ultraviolet light to erase the bit pattern.
To activate this mode, the programming equipment must force